Typewriter Talk

You are not logged in. Would you like to login or register?



14-3-2018 17:21:15  #141


Re: SG Owners Club

Soon to become a member of the club. I've arranged to collect an SG1 next week. Looking forward to comparing it to the Hermes Ambassador, which I absolutely love. Does anyone know if the plastic paper guide from an SG3 will fit the SG1? Thanks.
 

 

15-3-2018 15:07:55  #142


Re: SG Owners Club

Regarding your question about the paper guide, I believe so. But a question I have is, how do you remove the paper guide? I've looked at it but I can't figure out a way to remove the pins that hold it in place. Maybe that's not how you remove the guide? I'm sure there's a trick to it but I sure can't figure it out. (I have four SG1s and one SG3, and only one paper guide among all of them!) 

 

21-3-2018 14:17:32  #143


Re: SG Owners Club

Yesterday's excitement was driving for a couple of hours to bring home my first SG1. It is a bit tired! Peeling chrome plate on the carriage return, rock hard platen rubber with some cracking and I'm guessing missing sound damping felt from the top cover plate. A swift vacuum clean, wipe of oil on the carriage rails then straight on with a carbon ribbon. It's lovely! I stayed up til three in the morning tinkering and typing.

It is very noisy in use, making a metallic ringing sound from the back cover plate on the carriage - the side panels sound dull when tapped but this one is a bit like a gong. Should there be damping felt on this cover plate? The type slugs have 12 and 7.6 marked on them. It types ten characters to the inch. I like it a lot!

https://i.imgur.com/jVpwVUX.jpg

 

21-3-2018 16:07:45  #144


Re: SG Owners Club

5teve B wrote:

...the side panels sound dull when tapped but this one is a bit like a gong. Should there be damping felt on this cover plate?

​There should be sound dampening material throughout the machine. In every SG1 that I've come across the original open cell foam that was used by Olympia was in terrible shape, often crumbling and falling out of the machine. It's not uncommon for it to be missing entirely.

Although I haven't found it makes a big difference, I have replaced that foam in a couple of my machines. However, most often a noisy SG1 is one that has loose or improperly fitted covers or parts.  


"To save time is to lengthen life."
     Thread Starter
 

23-3-2018 21:09:08  #145


Re: SG Owners Club

I had the back cover of the carriage off on one of my SG1s a couple of days ago. I don't believe there ever was any sound dampening foam inside. However, I wonder whether your machine is missing the two piece washers (metal and rubber) between the screws on the back and where the screws mesh with the carriage frame. These can easily fall out if the back carriage cover is removed, and their absence might account for the resonance you're experiencing.

 

28-3-2018 07:39:27  #146


Re: SG Owners Club

Possibly mine is constructed differently. The 18" carriage rear cover is held in place by two screws at each end. These screw in from the sides. There are no screws along the whole of the back. The lower edge of the cover is not in contact with the carriage frame along the whole of its length and is free to resonate noisily. It was made in 1961. It may be about to get  a couple of slices of cork strategically placed to damp the vibration in the bottom edge.

 

15-4-2018 21:33:44  #147


Re: SG Owners Club

Fleetwing wrote:

Regarding your question about the paper guide, I believe so. But a question I have is, how do you remove the paper guide? I've looked at it but I can't figure out a way to remove the pins that hold it in place. Maybe that's not how you remove the guide? I'm sure there's a trick to it but I sure can't figure it out. (I have four SG1s and one SG3, and only one paper guide among all of them!) 

I take it you are referring to the clear plastic part. I would call this a paper rest; I'd call the tab which guides the left side of the paper the paper guide. If that's what you are referring to the pins are held in place by clips; given the embrittlement of 50 year old plastic though I wouldn't try just popping it out, but gently prying apart the clip to release the pin. The rests on the SG-1 are longer and more elaborate. but believe the SG-3 rest fits.
 

 

16-4-2018 06:19:21  #148


Re: SG Owners Club

Yes, paper rest (or paper support) is the right term. I find myself making that mistake from time to time. 

Not sure where those clips are -- I'll take another look. 

 

Board footera

 

Powered by Boardhost. Create a Free Forum

Typewriter Talk