You are not logged in. Would you like to login or register?

Resources » Platen size chart » 04-12-2018 21:11:17

Derrick1p1
Replies: 1

Go to post

Hello!

A while back I found a chart with the sizes (diameter, length, etc.) of many different typewriter models.
And of course, now I can’t find it. Why on earth I hadn’t saved it I do not know. Has anyone else come across this? If so, can you share the link?

Maintenance & Repairs » Typebars not reaching platen. Margin line lock working correctly. » 06-11-2018 02:55:47

Derrick1p1
Replies: 3

Go to post

Thank you both!
@thetypewriterman- Your suggestion made me sit back and look at it from a distance. And she hasn’t been treated kindly over the years. And most definitely been dropped...I think while in the case due to damage to the rear “bar” that helps lock it into place while in transit. I assumed a drop like this could have forced the carriage back, not allowing the type bars to reach the platen, which turned out to be the issue.

@beak- you were right! I wasn’t sure what to look for, but found it. I found four screws, two on each side that allows for adjustment of the carriage forward/back. It was all the way back, so I adjusted forward..and that fixed it. I was able to fix the second problem by adjusting the rollers to the right (by loosening the screw near the right roller, pulling the rollers to the right and then tightening it back).

Kind of. As you can imagine it was a domino effect. I’d fix  one issue, then another pops up related to that adjustment, and so on. Some tweeking  was needed due to past adjustments (thanks to typewriterman’s suggestion, I looked for evidence via markings on screws/parts). I think the drop may have bent the ribbon vibrator bc it was getting stuck. After some work I was able to get that working well. Then I began typing and the carriage would jump a space when using the “a” and “t” keys. I googled it and realized it was most certainly my technique. After just a bit of practice I got the “feel” of how I should be typing differently on a typewriter vs a keyboard. I thought I might sell her now that everything is working well, but I think I’d regret it. She’s pretty loud, but she and the case cleaned up very well and I like the look and feel of this one.

As a reward, lol, I ordered a Remington Noiseless model 7, with a case. Got it pretty cheap. Looks in decent shape- owner says it works- so I’ll see. Fingers crossed that if there are some repairs that I can figure them out.

Anyhow- thanks agai

Maintenance & Repairs » Typebars not reaching platen. Margin line lock working correctly. » 26-10-2018 12:24:54

Derrick1p1
Replies: 3

Go to post

Hello All,
 
I have a Royal Sabre (manufacture date June 1969).  I’m new to this and have done a bit of googling and searching here. This topic has been addressed, but I think my problem is not what was recommended in a past post.  I’ll post a 2nd issue, only just in case it has something to do with the main problem (#1).  If not, I’ll address #2 later. 
 
#1: My typebars are not reaching the platen.  Unless I slam them pretty hard, they will not make an impression or reach the paper.  I confirmed that the "line lock" mechanism that prevents the typebar from advancing when reaching a margin is performing correctly.  That mechanism, only activates when reaching the margin, preventing over typing as it should.  Otherwise, it releases and allows the bar to fully reach the back of the typebasket (not sure of the terminology, but it's the metal plate just below the ribbon/platen that stops the typebar).  I’ve tried to include a pic to help but not if I can upload the link since I haven't posted but once before here…you should be able to see the typebar touching the type basket rear plate…so technically I don’t think it could go any further, even if I forced it…that the limit.  From what I can see below, all parts are in good shape, nothing bent, they are clean/oiled and don’t seem to be “holding” the typebars back.  My gut tells me that something is “off” and out of kilter, not allowing the key to get to that last little bit of distance to hit the platen.  Could the basket have loosened keeping the bars back, or could the platen have loosened and shift back…or maybe a little of both?!
 
#2: The paper release lever doesn’t engage unless I put pressure down, up or in on the cylinder knobs.  Otherwise, the roller just “slides” as if I released the release level to straighten out the paper.  So I don’t hear the “click” when trying to return to another line…the paper stays stationary and the roller moves freely.  The

Type Talk » New Member Thread » 16-10-2018 14:12:16

Derrick1p1
Replies: 984

Go to post

Hello All,

I think I may have the portable typewriter bug.  I'm not a writer, so not sure what I'll do with my first one (Montgomery Ward/Signature 510d) made in June of '69.  Perhaps use my laptop less

I found another on ebay for $30.  Needs a repair that I think I may be able to figure out.  I'm pretty handy and always like to tinker, clean up/refurbish vintage items, so that is the attraction.  

During a visit to Asheville, I met a young man that had a desk/stool and an old portable typewriter.  He sat on the corner and typed poems for $.  He's a talented writer and my poem was great.  But I was more drawn to his typewriter than anything, and he told me the story behind it and how he acquired it.  Since then I've been scanning online.  Then I saw the 501d in great condition in an antique store.  I cleaned it up (didn't need much), ordered a ribbon and made 3 springs that were missing (what's up with not being able to purchase miniature springs!!!).  Anyhow, I made my own with some music wire and a drill, and voila!  it works. 

Glad to know there are other folks out there that appreciate these great machines!

Derrick

 

Board footera

 

Powered by Boardhost. Create a Free Forum