1 of 1- robmck
- Speed Champion
Offline - From: Seattle, WA
- Registered: 31-1-2022
- Posts: 373
SG-1 paper rollers
Looks like my SG-1's rollers are made of cork. Also, they're cracking. What have other folks done to freshen up their rollers? I suppose I could ship everything off to J.J. Short, but I imagine that the hardness would be different with rubber than cork, so the diameters might be different?
Anyway, would welcome any thoughts folks have.
- Pete E.
- Typewriter Talk Elite
Offline
- From: Idaho - USA
- Registered: 23-6-2020
- Posts: 2,370
Re: SG-1 paper rollers
Rob,
You might stop by a couple of different auto parts stores. They usually have a nice variety of vacuum line rubber hose in various OD/ID's and you have them cut it by the linear foot. In my home town...O'Reilly's and Auto-Zone keep up pretty good inventory from which to choose.
- skywatcher
- Moderator
Offline
- From: The Prairies of Alberta
- Registered: 14-3-2013
- Posts: 734
Re: SG-1 paper rollers
Hi Rob
As Pete says, vacuum line or fuel line can work quite well for feed roll replacement rubber. The feed rolls are usually much softer than the platen, so a person may even be able to use surgical tubing of the correct diameter. The diameter of feed roll is also not as critical at platen diameter, so as long as the rolls can rotate freely within the paper pan slots, grip the paper and release it when the paper release lever is moved, they should work. With the condition of your cork feed roll, you have nothing to lose by doing some experimenting. Hope this gives you some ideas,
Sky
We humans go through many computers in our lives, but in their lives, typewriters go through many of us.
In that way, they’re like violins, like ancestral swords. So I use mine with honor and treat them with respect.
I try to leave them in better condition than I met them. I am not their first user, nor will I be their last.
Frederic S. Durbin. (Typewriter mania and the modern writer)
- thetypewriterman
- Key Master
Offline
- From: Leiston, England
- Registered: 29-5-2013
- Posts: 919
Re: SG-1 paper rollers
Just for interest, I think that your feedrolls may have been re-covered in cork/rubber compound, something that Triumph-Adler did as standard but was also offered as an aftermarket option by rubber firms such as Ames. Of course, it is the rubber element which has deteriorated and split, I have seen pure cork feedrolls from the 1930's (admittedly a thicker layer on the core) which are still perfectly servicable - as are cork platens this old.
- robmck
- Speed Champion
Offline
- From: Seattle, WA
- Registered: 31-1-2022
- Posts: 373
Re: SG-1 paper rollers
Thanks all! I'll look into tubing to replace these.
Tom, I'm curious about the cork and cork/rubber compound paper feed rollers: it sounds like these were an aftermarket option. What were the perceived advantages of these vs 100% rubber? Cost? Performance? Feel?
- •
Thread Starter- thetypewriterman
- Key Master
Offline
- From: Leiston, England
- Registered: 29-5-2013
- Posts: 919
Re: SG-1 paper rollers
The only manufacturer that used cork/rubber compound from new was Triumph-Adler, although it could be ordered as an aftermarket alternative for other makes when feedrolls were being re-covered. The advantage was supposed to be durability. Cork lasts almost indefinitely, but never grips as well as rubber. Mixing the two should in theory give the advantages of both. The mixture does indeed last longer than rubber alone, but as you can see from the photo, it will will split eventually - particularly if the coating is thin. The disadvantage is that it never grips as well as rubber, although a little better than cork on its own.
